Accufast Kt Tabber Service Manual

Service Manual Accufast. Manual-accufast-kt-tabber-xl-labeler/ a to b tv service manuals a training manual a trump mill repair manual a uberti cattleman 357. If searching for a ebook Service manual accufast in pdf format, then you have come on to faithful site. We furnish utter release of this ebook in txt, DjVu, ePub, doc, PDF.

• • • • • • • • • • • • • • • • • • • • • • • • • • • • Go Back to: > > > Accufast KT 1.5 Tabletop Tabbing Machine The ACCUFAST KT 1.5 is a feature rich basic tabbing machine. The KT 1.5 lets you use 1' or 1.5' mailing tabs / wafer seals. It uses plain circular or rectangular tabs either opaque or clear. It tabs pieces up to ¼” in thickness and it rolls the waste up on a take up spool.

Software igo8 per autoradio cinesiologia. At speeds of 15,000 per hour or so, it is a stretch to refer to the ACCUFAST KT 1.5 as a basic tabber – there’s a lot of the professional in the KT. With the addition of the KT-TT Tabber at the end of a KT tabber you can apply an additional tab in the same pass. For users with an existing Accufast KT, you can have your KT converted to a KT 1.5 by Accufast.

In addition to converting your Accufast KT to a KT 1.5, it will be refurbished with any needed parts to get your Accufast KT 1.5 running like new! Please call 800-899-4402 for more information and pricing! MSRP Accufast KT 1.5 (Tabber only): $3,700.00 Accufast KT 1.5 w/ FX feeder: $5,460.00 Accufast KT-TT: $3,625.00 Technical Specifications • applies 1 tab per piece • tabs 15,000 pieces per hour • tabs pieces 5' to 12' wide, from 20 lb. Thin to 1/4' thick, coated and uncoated • runs a variety of 1' or 1.5' tabs: paper & clear, circles & rectangles • built-in waste take-up spool • weighs 47 pounds • measures 10'l x 17'h x 21'w • uses 115 volts 2 amps 60 Hz or 230 volts 1 amp 50 Hz • goes in-line with ACCUFAST and other tabletop Labelers and Printers • its outstanding feature is its ability to run virtually any 1' or 1.5' tab, and tab virtually any piece.

How do I adjust and clean the Accufast KT Tab Sensor? Published: December 3, 2011 UPDATED If you experience tabbing problems on the Accufast KT, tune the sensor for – Also know as a KT Sensor Reset: WARNING DO NOT PLACE FINGERS OR TOOLS BETWEEN OR NEAR MOVING PARTS.

1) Turn the POWER SWITCH off. 2) Remove any tabs and debris from the peel point area through the INSPECTION WINDOW on the input end, below the threading path. CAUTION IF ALL TABS AND DEBRIS ARE NOT REMOVED FROM THE PEEL POINT AREA BEFORE CLEAR TAB IS ACTIVATED, THE SENSOR’S DEFINITION OF CLEAR TABS WILL CHANGE AND CLEAR TABBING WILL BE PREVENTED. On the product entry side, there is an elongated hole under where the tabs peel off, see below If you look inside the hole, you will see the bottom portion of the sensor.

(The black circle in the white plastic, see photo below) Clean it off with some. Also, make sure no tabs are anywhere in the path. If you remove the tabs and look from the exit side, you can see the top portion of the sensor. In the photo below, look for the rectangle with the nut on it. The sensor is on the bottom of the white housing directed down at the lower sensor. Once you have this area clean turn the KT back on and, 3) Toggle CLEAR TAB off and wait, a few seconds 4) Toggle CLEAR TAB on. 5) Toggle ON/OFF until a tab advances to the peel point and the TAB READY light illuminates.Your sensor has now been re-calibrated!Another thing to check is to make sure the tabs are threaded correctly!

See photos below. Below Shows to correct way to thread the Accufast KT Tabber Correct Incorrect Do you need a KT? Give All For Mailers a call at 866-430-2874 New and Used Accufast KT available! Need Need Replacement Parts? SuppliesForMailers.com has them!